HP SCSI DAT

[Michael Macek]

Zdravim vsechny priznivce Linuxu,
poridili jsme si HP SCSI DATku DDS-2 C1533A a nejak se mi ji nedari
rozchodit pod Linuxem. SCSI radic mam Adaptec 2940.
Bios jednotku rozpozna v pohode, Linux pozna SCSI radic, detekuje najake
zarizeni, ale nevypise jeho oznaceni ani vyrobce. Pokusy pouzti napr mt na
/dev/st0 nebo 1 konci hlaskou "No such device". Muj dojem z toho je, ze
Linux DATku nedetekuje.

Jadro 2.0.27, distribuce Debian 1.1, podpora pro SCSI pasky v jadre mam,
SCSI-HOWTO jsem cetl ale nepomohlo. Problem bude mozna v tom, ze v SCSI se
prilis nevyznam...
 
Nemate s tim nekdo zkusenosti? Pripojuji hlasky kernelu pri bootu.

Zdravi 
  Michael Macek

-------------------------------------------------------------------------
aic7xxx: BurstLen = 8 DWDs, Latency Timer = 64 PCLKS
aic7xxx: AHA-2940 Rev B.
aic7xxx: devconfig = 0x580.
aic7xxx: Reading SEEPROM...done.
aic7xxx: Extended translation enabled.
aic7xxx: Memory check yields 16 SCBs, paging not enabled.
AHA-2940 (PCI-bus), I/O 0xfc00, Mem 0xffbef000:
    irq 9
    bus release time 40 bclks
    data fifo threshold 100%
    SCSI CHANNEL A:
        scsi id 7
        scsi selection timeout 256 ms
        scsi bus reset at power-on enabled
        scsi bus parity enabled
        scsi bus termination (low byte) enabled
aic7xxx: Downloading sequencer code...done.
aic7xxx: Resetting the SCSI bus...done.
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.0/3.2/4.0
scsi : 1 host.
scsi0: Scanning channel A for devices.
scsi0: Target 1, channel A, now synchronous at 10.0MHz, offset 8.
scsi : aborting command due to timeout : pid 2, scsi0, channel 0, id 1,
lun 0 0x
03 00 00 00 10 00 
aic7xxx: (abort) Aborting scb 0, TCL 1/0/0
scsi : aborting command due to timeout : pid 2, scsi0, channel 0, id 1,
lun 0 0x
03 00 00 00 10 00 
aic7xxx: (abort) Aborting scb 0, TCL 1/0/0
SCSI host 0 abort (pid 2) timed out - resetting
SCSI bus is being reset for host 0 channel 0.
aic7xxx: (reset) target/channel 1/0
aic7xxx: (abort_reset) scb state 0x1, Data-In phase, SCSISIGI = 0xc6
aic7xxx: (abort_scb) asserted ATN - bus device reset in message buffer.
SCSI host 0 channel 0 reset (pid 2) timed out - trying harder
SCSI bus is being reset for host 0 channel 0.
aic7xxx: (reset) target/channel 1/0
aic7xxx: (reset_device) target/channel -1/A, active_scb 0
aic7xxx: (match_scb) comparing target/channel -1/A to scb 1/A
aic7xxx: (reset_channel) Resetting current channel A
aic7xxx: (reset_channel) Channel reset, sequencer restarted
aic7xxx: (done_aborted_scbs) Aborting scb 0, TCL=1/0/0
  Vendor:           Model:                   Rev:     
  Type:   Direct-Access                      ANSI SCSI revision: 00
scsi : detected total.
-----------------------------------------------------------------------