lilo a Syquest
Petr Her~man
Petr.Herman na lfmotol.cuni.cz
Pondělí Září 23 11:48:48 CEST 1996
> : 1) nemohu namontovat vymmeny disk Syquest 270Mbyte IDE.
> : kdyz dam
> : mount -t msdos /dev/hdd1 /sda
> :
> : tak mi vynada:
> :
> : hdd:<5>ll_rw_block: device 16:40: only 512-char-blocks implemented (1024)
> : unable to read partition table
> : hdd:<5>ll_rw_block: device 16:40: only 512-char-blocks implemented (1024)
> : unable to read partition table
> : FAT bread failed
> : mount: wrong fs type, bad option, bad superblock on /dev/hdd1,
> : or too many mounted file systems
Ja mam taky problemy se SYQUESTem EZ135Drive 135 MB.
(Predtim jsme meli 270 MB ale byly s nim porad opakovane problemy,
tak jsme ho radeji vymenili za mensi v domeni, ze bude aspon
spolehlivejsi.)
Pred casem se mi podarilo ho zprovoznit na /dev/hdb.
Porusil jsem ale vazne zasadu "nestourat do toho,
co chodi" a tak jsem na /dev/hdb dal misto SYQUESTa druhy IDE HDD
a SYQUEST prehodil na druhou desku IDE radice, tj. na /dev/hdc
Ale pri mountovani mi taky hlasi:
/etc# mount -t msdos /dev/hdc1 /SYQUEST
mount: wrong fs type or bad superblock on /dev/hdc1
> Mam dva napady, ale nevim, jestli aspon jeden zabere:
> 1) Zkusit /dev/hdd misto /dev/hdd1
nepomohlo:
/etc# mount -t msdos /dev/hdc /SYQUEST
mount: wrong fs type or bad superblock on /dev/hdc
> 2) Zkusit dat -o bs=512 nebo -o bs=1024 pri spousteni programu mount.
taky ne.
fdisk mi rekne:
-----------------------------------------------------
/etc# fdisk /dev/hdc
The number of cylinders for this disk is set to 16896.
This is larger than 1024, and may cause problems with:
1) software that runs at boot time (e.g., LILO)
2) booting and partitioning software form other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Warning: invalid flag 6a55 of partition table 4 will be corrected by w(rite)
Command (m for help): p
Disk /dev/hdc: 16 heads, 32 sectors, 16896 cylinders
Units = cylinders of 512 * 512 bytes
Device Boot Begin Start End Blocks Id System
/dev/hdc1 * 2096197 2097185 4194784536985584 6 DOS 16-bit >=32M
Partition 1 does not end on cylinder boundary:
phys=(383, 79, 32) should be (383, 15, 32)
-------------------------------------------------------
Nevite nekdo co je to ten flag 6a55?
Pocet heads a sectors souhlasi, ale to reportovany mnozstvi cylindru
je dost divoky (ve skutecnosti ma 512 cyl.) a ta hausnumera
v partition table taky.
K tomu jen pozn, ze ten SYQUEST byl formatovany pod W95 :-(((
s dlouhymi jmeny souboru. Zkusil bych dat (w)rite :-) ale
sef se desi, ma na nem vzacna data :-(
O tech W95 filesystemech toho moc nevim, nicmene ziju v domeni,
ze by to s partition tabulama nemelo mit nic tak moc do cineni.
Mam ide.c Version 5.41 z kernelu 1.2.13., ze by ho ty Woknouzy
tak zblbly?
Divny je jen, ze kdyz to bylo jako /dev/hdb, tak to slo cist,
a na /dev/hdc to takhle vzdoruje.
Po tom, co jsem pridal dalsi radic ide1 jsem pustil MAKEDEV.ide
podle navodu v README.ide:
To access devices on the 2nd/3rd/4th interfaces, device entries must
first be created in /dev for them. To create such entries,
simply run the included shell script: MAKEDEV.ide
> -Yenya
Petr Herman
Další informace o konferenci Linux