miroMedia Online

[Slavek Banko (axis)]

To, co mi vratil pnpdump k predchozimu emailu pripojoval. Jestli 
pripojeny soubor neprosel, tak tu je jeho obsah:

# $Id: pnpdump.c,v 1.10 1997/07/14 22:30:47 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Board 1 has serial identifier de 64 01 00 01 34 0c 32 35

# (DEBUG)
(READPORT 0x0203)
(ISOLATE)
(IDENTIFY *)

# Card 1: (serial identifier de 64 01 00 01 34 0c 32 35)
# MIR0c34 Serial No 1677787137 [checksum de]
# Version 1.0, Vendor version 0.3
# ANSI string -->Mwave Plug & Play Multimedia Adapter<--
#
# Logical device id MIRc340
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be 
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE MIR0c34/1677787137 (LD 0
#     ANSI string -->DSP<--
#     IRQ 3, 4, 5, 6, 7, 9, 10, 11, 14 or 15.
#         High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 3 (MODE +E)))
#     First DMA channel 0, 1, 2, 3, 6 or 7.
#         16 bit DMA only
#         Logical device is a bus master
#         DMA may not execute in count by byte mode
#         DMA may execute in count by word mode
#         DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))

# Multiple choice time, choose one only !

#     Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0140
#             Maximum IO base address 0x01f0
#             IO base alignment 16 bytes
#             Number of IO addresses required: 16
# (IO 0 (BASE 0x0140))

#     End dependent functions
# (ACT Y)
))
#
# Logical device id MIRc341
#     Device support I/O range check register
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be 
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE MIR0c34/1677787137 (LD 1
#     ANSI string -->Joystick<--
#     Compatible device id PNPb02f
#     Fixed IO base address 0x0200
#         Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# (ACT Y)
))
#
# Logical device id MIRc342
#     Device support I/O range check register
#     Device supports vendor reserved register @ 0x38
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be 
changed if required
# Don't forget to uncomment the activate (ACT Y) when happy

(CONFIGURE MIR0c34/1677787137 (LD 2
#     ANSI string -->Radio<--

# Multiple choice time, choose one only !

#     Start dependent functions: priority acceptable
#       Logical device decodes 16 bit IO address lines
#             Minimum IO base address 0x0100
#             Maximum IO base address 0x03c0
#             IO base alignment 64 bytes
#             Number of IO addresses required: 4
# (IO 0 (BASE 0x0100))

#     End dependent functions
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)

# Returns all cards to the "Wait for Key" state
(WAITFORKEY)

Nevim, co v nem kde nastavit....

Slavek.

-----Puvodni zprava-----
Od:	Petr Stanek [SMTP:snek na penguin.cz]
Odeslano:	10. prosince 1998 13:36
Komu:	Multiple recipients of list
Predmet:	Re: miroMedia Online

"Slavek Banko (axis)" wrote:
>
> Muzete mi nekdo pomoci (jiz nechci kvuli internauteni a zvuceni
> rebootovat do Windows).

Jo pokud je to opravdu SB kompatibilni a neni to kopatibilta pomoci SW.

Jestli se ti v pnpdump obevi, tak staci odpoznamkovat vhodne nastaveni
(je tam vzdy nabidka vice moznosti) a pak isapnp upraveny_soubor a je to
hotovo.

Samozrejmne v jadre nebo modulu musi byt nastaveny vami uvedene hodnoty
pokud to neumi autodetekova.

Snek
--
-----------------------------------------------------------------------
Snek Petr Stanek          mailto:snek na penguin.cz     tel.: 069/6656 318
Server pro podporu UNIXu     Debian GNU Linux     http://www.penguin.cz