scanner Acer 3300U - delší

[Pavel ŠVARC]

        Zdravím ctěnou konferenci,

  mám problém se %subj% pročetl jsem už snad všechno a zkusil mnohem víc a 
scanner nic :O((( Popíšu situaci mám RH7.1en jádra 2.4.2-2.a 2.4.4 a SANE 
1.0.3 Po startu se načtou moduly 
-- cut messages --
May 24 08:01:36 samyce kernel: usb.c: registered new driver usbdevfs
May 24 08:01:36 samyce kernel: usb.c: registered new driver hub
May 24 08:01:36 samyce kernel: usb-uhci.c: $Revision: 1.251 $ time 11:47:40 
Apr 26 2001
May 24 08:01:36 samyce kernel: usb-uhci.c: High bandwidth mode enabled
May 24 08:01:36 samyce kernel: PCI: Found IRQ 9 for device 00:04.2
May 24 08:01:36 samyce kernel: usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 9
May 24 08:01:36 samyce kernel: usb-uhci.c: Detected 2 ports
May 24 08:01:36 samyce kernel: usb.c: new USB bus registered, assigned bus 
number 1
May 24 08:01:36 samyce kernel: hub.c: USB hub found
May 24 08:01:36 samyce kernel: hub.c: 2 ports detected
May 24 08:01:36 samyce kernel: hub.c: USB new device connect on bus1/2, 
assigned device
number 2
May 24 08:01:36 samyce kernel: usb.c: USB device 2 (vend/prod 0x4a5/0x20b0) 
is not claimed by any active driver.
-- end messages --
potom #modprobe scanner vendor=0x4a5 product=0x20b0
-- cut messages --
May 24 08:03:34 samyce kernel: scanner.c: probe_scanner: User specified USB 
scanner -- Vendor:Product - 4a5:20b0
-- end messages --
potom je nutno nahrát firmware do scanneru 
#acerfirm -v u176v041.bin /dev/usbscanner
tento příkaz neprojde vypíše (tedy asi dvakrát prošel pokud byl scanner 
předtím activován pod Win98, ale teď už se mi ani to nedaří)
Scanner Information (from scanner)
        Vendor:
        Version:
        Model:
        Firmware date:
no uznejte moc hezký ale jinak nic moc :O(((
# export SANE_DEBUG_SNAPSCAN=255
# scanimage -d snapscan:/dev/usbscanner
[sanei_debug] Setting debug level of snapscan to 255.
[snapscan] sane_snapscan_init
[snapscan] add_device(/dev/usbscanner)
[snapscan] mini_inquiry
[snapscan] mini_inquiry: sanei_scsi_cmd command failed: Error during device 
I/O
[snapscan] add_device: mini_inquiry failed with Error during device I/O.
[snapscan] sane_snapscan_open (/dev/usbscanner, 0xbffff4dc)
[snapscan] find_device
[snapscan] sane_snapscan_open: device "/dev/usbscanner" not in current 
device list.
scanimage: open of device snapscan:/dev/usbscanner failed: Invalid argument
[snapscan] sane_snapscan_exit
No a to je celý :O(((

Máte někdo nějakej nápad nebo zkušenost jak s USB tak se SANE ??

Stefan

PS: pod Win98 scanner normálně funkční