AC97 + QDI KuDoz 7

[Milan KUNDRAT]

Dobry den

Kupil som si dosku QDI KuDoz 7, ktora ma zabudovany AC97, ktory neviem 
rozbehnut. Boli nejake chabe pokusy, ktore radsej nebudem popisovat :-)

Toto je vypis lspci -vvv (vyhodil som udaje o grafike, sietovke, usb a ide):

00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
        Subsystem: VIA Technologies, Inc. VT8367 [KT266]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 8
        Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: <available only to root>

00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 
[Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: ec000000-edffffff
        Prefetchable memory behind bridge: e0000000-e7ffffff
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
        Capabilities: <available only to root>

00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
        Subsystem: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping+ SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Capabilities: <available only to root>

00:11.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio 
Controller (rev 30)
        Subsystem: VIA Technologies, Inc.: Unknown device 4161
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 5
        Region 0: I/O ports at e400 [size=256]
        Capabilities: <available only to root>

Mam malo skusenosti s oss a ziadne s alsou. Prijatelny je ktorykolvek sposob.
Nema niekto skusenost s nahodenim tejto zvukovky?

dakujem
-- 
Milan KUNDRAT
email: mkundrat na penguin.cz
icq: 172420788
http://www.penguin.cz/~mkundrat
tel:++421904496438