SMART (delsi)

[Vaclav Dvorsky]

EHP napsal(a):

Dobry den,
ja sice nevim, ale rad bych se pripojil s dotazem. Muj disk je Seagate 
Barracuda IV 40GB a smartctl mi vypisuje:

smartctl -v /dev/hda1
Vendor Specific SMART Attributes with Thresholds:
Revision Number: 10
Attribute  Status   Flag  Value   WorstEver   Threshold        Raw Value
    1    0x000f       081         078         034     00000e1bf2ec
    3    0x0003       070         070         000     000000000000
    4    0x0032       100         100         020     000000000005
    5    0x0033       100         100         036     000000000000
    7    0x000f       063         060         030     00000024fb66
    9    0x0032       100         100         000     00000000006c
   10    0x0013       100         100         097     000000000000
   12    0x0032       100         100         020     00000000001f
  194    0x0022       038         045         000     000000000026
  195    0x001a       081         078         000     00000e1bf2ec
  197    0x0012       100         100         000     000000000000
  198    0x0010       100         100         000     000000000000
  199    0x003e       200         200         000     000000000000
  200    0x0000       100         253         000     000000000000
  202    0x0032       100         253         000     000000000000

> Vypis z hdparmu:
> 
>  Model=ST380021A, FwRev=3.19, SerialNo=3HV1YQP9
>  Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
>  RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
>  BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
>  CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=156301488
>  IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
>  PIO modes: pio0 pio1 pio2 pio3 pio4
>  DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
>  AdvancedPM=no WriteCache=enabled
>  Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5
> 

hdparm -i /dev/hda

/dev/hda:

  Model=ST340016A, FwRev=3.19, SerialNo=3HSDMBLL
  Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
  RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
  BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
  CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
  IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
  PIO modes:  pio0 pio1 pio2 pio3 pio4
  DMA modes:  mdma0 mdma1 mdma2
  UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
  AdvancedPM=no WriteCache=enabled
  Drive conforms to: device does not report version:  1 2 3 4 5

Proste u smartctl nevidim rozepsanou teplotu disku, zda se mi, ze by 
mohla byt na 194, ale jisty si nejsem. Je mozne, ze by hlaska
device does not report version: 1 2 3 4 5 znamenala, ze u smartctl 
nebudou hodnoty oznaceny slovne nebo je to jeste uplne jinak a ten disk 
teplotu merit neumi?
Diky

-- 
Vaclav Dvorsky
http://www.akira.cz
emajl: hufhendr na akira.cz, iso-8859-2
tel: +420608021530, PGP: 0xD38E2CA7, X.509 supported