sony f828 + slackware

[Petr Sigut]

Dne Sat, 03 Jan 2004 20:13:58 +0100
Tomáš Chaloupka <chalucha na centrum.cz> napsal:

 
> hub.c: new USB device 00:04.3-2, assigned address 2
> scsi1 : SCSI emulation for USB Mass Storage devices
>    Vendor: Sony      Model: Sony DSC          Rev: 3.22
>    Type:   Direct-Access                      ANSI SCSI revision: 02
> Attached scsi removable disk sda at scsi1, channel 0, id 0, lun 0
> SCSI device sda: 253696 512-byte hdwr sectors (130 MB)
> sda: Write Protect is off
>   sda: sda1
> USB Mass Storage device found at 2
> 
> pak dam jen mount -t vfat /dev/sda1 /mnt/floppy a je to
> 
> S distribucnim jadrem by to melo byt ok.
> Podle me je potreba zkompilovat nasledujici (nerikam ze to tak opravdu
> je, jen mi to tak chodi)
> SCSI disc support
> SCSI generic support
> USB mass storage
> UHCI support
> 
> ja mam vsechno tohle primo v jadre 2.4.23.
> 
> BTW posledni stable slack9.1 ma jadro 2.4.22.
> 
> Treba jsou ty fotaky kapku rozdilny, ja mam precijen uz postarsi model
> DSC S-75 :)
> BTW posledni stable slack9.1 ma jadro 2.4.22.

Vyslo nove jadro 2.4.23, ktere opravovalo chyby, tak jsem ho stahl -
original slack.

TGZ balicek ma ale tohle info:

 (Linux kernel without SCSI controller support)
A Linux kernel for computers that do not need SCSI support.
You MUST install a kernel image in order for your system to
boot. This kernel supports IDE hard drives and IDE CD-ROM
drives.  Other drivers (such as for CD-ROM drives on
proprietary interfaces, or ethernet cards) may be loaded as
modules.  See /etc/rc.d/rc.modules for examples.

Pisou ze tam zadna SCSI podpora neni, ale treba vypalovacka mi bezi pred
ide-scsi, ale to bude asi neco jineho.


root na phax:~# modprobe usb-uhci (bez pripojeneho fotaku)

/lib/modules/2.4.23/kernel/drivers/usb/host/usb-uhci.o.gz: init_module:
No such device/lib/modules/2.4.23/kernel/drivers/usb/host/usb-uhci.o.gz:
Hint: insmod errors can be caused by incorrect module parameters,
including invalid IO or IRQ parameters.      You may find more
information in syslog or the output from
dmesg/lib/modules/2.4.23/kernel/drivers/usb/host/usb-uhci.o.gz: insmod
/lib/modules/2.4.23/kernel/drivers/usb/host/usb-uhci.o.gz
failed/lib/modules/2.4.23/kernel/drivers/usb/host/usb-uhci.o.gz: insmod
usb-uhci failed

a pak dmesg tohle pribyde: (bez pripojeneho fotaku)
usb-uhci.c: $Revision: 1.275 $ time 18:28:09 Dec  1 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
ISO 9660 Extensions: RRIP_1991A
usb-uhci.c: $Revision: 1.275 $ time 18:28:09 Dec  1 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:28:09 Dec  1 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb-uhci.c: $Revision: 1.275 $ time 18:28:09 Dec  1 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver

Ze by to usb-uhci bylo natvrdo v jadre?

Ale po pripojeni fotaku mi v dmesg nepribyde nic... Mam pocit ze chyba
je v tom ze nejde zavest modul usb-ohci (pise to same jako usb-uhci) a
jadro se mi moc prekompilovavat nechce, kdyz pak vyjdou opravu tak jen
stahnu distribucni, takhle budu kompilovat znova...

Diky za pomoc, napada vas jeste neco?

-- 
Petr Šigut
petr.sigut na atlas.cz
ICQ: 154651919