lifebook C1020, VIA AC97 modem a VIA AC97 audio nefunguju sucasne
Miroslav Betak
betak na orga.sk
Středa Listopad 3 11:07:06 CET 2004
Dobry den
Mam nasledovny problem:
Nainstalovany operacny system Fedora Core 2 na notebooku lifebook
Fujitsu-Siemens C1020.
Po spusteni wvdial som vzdy skoncil , pri hlaske "NO CARRIER". Pozrel
som sa do /proc/interrupts a zistil som, ze rovnake prerusenie vyuziva
modul hsfmc97via aj modul VIA8233. Preto som unloadol zodpovedajuci
modul snd_via82xx, znovu spustil wvdial, ale znovu som zastal pri
rovnakej hlaske "NO CARRIER".
Nasledne na tom som zahesoval riadok z /etc/modprobe.conf "# alias
sn-card-0 snd-via8233," rebootol masinu , spustil wvdial a okamzite sa
vytvorilo spojenie.
V suvislosti s tym mam nasledovne otazky:
1., preco wvdial funguje len vtedy ak od restartu nebol natiahnuty
modul snd_via82xx a preco po jeho natiahnuti a removnuti nie ?
2., preco sa mi nepodarilo priradit ine prerusenia tymto dvom
zariadeniam po zadani parametrov jadra "acpi_irq_balance
acpi_irq_pci=11,13,...." ?
3. ako by som mohol dosiahnut stav, v ktorom mi bude chodit modem aj
audio sucasne ?<>
<>Za Vase vecne odpovede vopred dakujem
Miro
--------------------------------------------------------------------
dmesg
<>Linux version 2.6.8-1.521 (bhcompile na tweety.build.redhat.com) (gcc
version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 Mon Aug 16 09:01:18
EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<>BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000eff0000 (usable)
BIOS-e820: 000000000eff0000 - 000000000effffc0 (ACPI data)
BIOS-e820: 000000000effffc0 - 000000000f000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
239MB LOWMEM available.
zapping low mappings.
On node 0 totalpages: 61424
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 57328 pages, LIFO batch:13
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 OID_00 ) @ 0x000e5010
ACPI: RSDT (v001 INSYDE RSDT_000 0x00000001 _CSI 0x00010101) @ 0x0efffbc0
ACPI: FADT (v001 INSYDE FACP_000 0x00000100 _CSI 0x00010101) @ 0x0efffac0
ACPI: BOOT (v001 INSYDE SYS_BOOT 0x00000100 _CSI 0x00010101) @ 0x0efffb50
ACPI: DBGP (v001 INSYDE DBGP_000 0x00000100 _CSI 0x00010101) @ 0x0efffb80
ACPI: DSDT (v001 FUJITS EF4 0x00000419 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: ro root=/dev/hda17 acpi_irq_balance
acpi_irq_pci=10,11,3,4,6,7,5,13
mapped 4G/4G trampoline to ffff3000.
Initializing CPU#0
CPU 0 irqstacks, hard=023c7000 soft=023c6000
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1994.931 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 239484k/245696k available (2012k kernel code, 5520k reserved,
651k data, 140k init, 0k highmem)
Calibrating delay loop... 3923.96 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security
failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebf9ff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebf1ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
Freeing initrd memory: 189k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xe8964, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 1)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 7 9 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 7 *9 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 7 *10 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 7 *10 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 7
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 7 (level, low) -> IRQ 7
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
ACPI: PCI interrupt 0000:00:0a.1[B] -> GSI 4 (level, low) -> IRQ 4
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 3
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:00:11.4[D] -> GSI 3 (level, low) -> IRQ 3
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:11.6[C] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 7 (level, low) -> IRQ 7
vesafb: probe of vesafb0 failed with error -6
Simple Boot Flag at 0x37 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1099473773.907:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 9488DB81FF525AA3
- User ID: Red Hat, Inc. (Kernel Module GPG key)
ksign: invalid packet (ctb=00)
Unable to load default keyring: error=74
PCI: Via IRQ fixup for 0000:00:11.2, from 10 to 3
PCI: Via IRQ fixup for 0000:00:11.3, from 10 to 3
PCI: Via IRQ fixup for 0000:00:11.4, from 10 to 3
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1 C2, 16 throttling states)
ACPI: Thermal Zone [TZN0] (48 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA P4M266x/P4N266 chipset
agpgart: Maximum main memory to use for agp memory: 189M
agpgart: AGP aperture is 64M @ 0xa0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI interrupt 0000:00:11.1[A]: no GSI
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK4018GAS, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: QSI DVD-ROM SDR-083, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB), CHS=65535/16/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12
hda13 hda14 hda15 hda16 hda17 >
hdc: ATAPI 24X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
Firmware: 5.9
Sensor: 27
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
-> pass-through port
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
serio: Synaptics pass-through port at isa0060/serio4/input0
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 4681)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 140k freed
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
EXT3 FS on hda17, internal journal
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm na uk.sistina.com
cdrom: open failed.
Adding 265032k swap on /dev/hda6. Priority:-1 extents:1
hsfengine: module license 'see LICENSE file distributed with driver'
taints kernel.
ACPI: PCI interrupt 0000:00:11.6[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.6 to 64
ttySHSF0 at I/O 0xe200 (irq = 10) is a Conexant HSF softmodem
(PCI-1106:3068-10cf:118e)
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 3 (level, low) -> IRQ 3
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0xe000, 00:e0:00:9a:9c:4d, IRQ 3
eth0: Identified 8139 chip type 'RTL-8139C'
ip_tables: (C) 2000-2002 Netfilter core team
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
Disabled Privacy Extensions on device 0235c2a0(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
eth0: no IPv6 routers present
spurious 8259A interrupt: IRQ7.
ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
0002667.079: DevMgr_StartCallingTone - Fax element doesn't
exist0002719.986: DevMgr_StartCallingTone - Fax element doesn't
exist0002772.885: DevMgr_StartCallingTone - Fax element doesn't
exist0002935.062: DevMgr_StartCallingTone - Fax element doesn't
exist0002987.967: DevMgr_StartCallingTone - Fax element doesn't
exist0003040.869: DevMgr_StartCallingTone - Fax element doesn't
exist0003093.765: DevMgr_StartCallingTone - Fax element doesn't
exist0003146.670: DevMgr_StartCallingTone - Fax element doesn't
exist0003199.576: DevMgr_StartCallingTone - Fax element doesn't
exist0003252.484: DevMgr_StartCallingTone - Fax element doesn't
exist0003305.386: DevMgr_StartCallingTone - Fax element doesn't
exist0003358.288: DevMgr_StartCallingTone - Fax element doesn't
exist0003411.190: DevMgr_StartCallingTone - Fax element doesn't
exist0003464.092: DevMgr_StartCallingTone - Fax element doesn't
exist0003517.001: DevMgr_StartCallingTone - Fax element doesn't
exist0003569.924: DevMgr_StartCallingTone - Fax element doesn't
exist0003622.826: DevMgr_StartCallingTone - Fax element doesn't
exist0003675.730: DevMgr_StartCallingTone - Fax element doesn't
exist0003728.631: DevMgr_StartCallingTone - Fax element doesn't
exist0003781.534: DevMgr_StartCallingTone - Fax element doesn't
exist0003834.436: DevMgr_StartCallingTone - Fax element doesn't
exist0003887.341: DevMgr_StartCallingTone - Fax element doesn't
exist0003940.239: DevMgr_StartCallingTone - Fax element doesn't
exist0003993.144: DevMgr_StartCallingTone - Fax element doesn't
exist0004046.052: DevMgr_StartCallingTone - Fax element doesn't
exist0004098.949: DevMgr_StartCallingTone - Fax element doesn't
exist0004151.842: DevMgr_StartCallingTone - Fax element doesn't
exist0004204.772: DevMgr_StartCallingTone - Fax element doesn't
exist0004257.666: DevMgr_StartCallingTone - Fax element doesn't
exist0004310.568: DevMgr_StartCallingTone - Fax element doesn't
exist0004363.461: DevMgr_StartCallingTone - Fax element doesn't
exist0004416.353: DevMgr_StartCallingTone - Fax element doesn't
exist0004469.261: DevMgr_StartCallingTone - Fax element doesn't
exist0004522.171: DevMgr_StartCallingTone - Fax element doesn't
exist<6>ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 10 (level, low) ->
IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
------------------------------------------------------------------------
lsmod
Module Size Used by
snd_via82xx 24165 0
snd_ac97_codec 58821 1 snd_via82xx
snd_pcm 83529 1 snd_via82xx
snd_timer 25413 1 snd_pcm
snd_page_alloc 8393 2 snd_via82xx,snd_pcm
gameport 4033 1 snd_via82xx
snd_mpu401_uart 7361 1 snd_via82xx
snd_rawmidi 21733 1 snd_mpu401_uart
snd_seq_device 6473 1 snd_rawmidi
snd 45477 7
snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 7713 1 snd
md5 3905 1
ipv6 217349 10
8139too 22465 0
mii 3777 1 8139too
hsfmc97ali 50580 0
hsfmc97via 48536 0
hsfmc97ich 50192 0
hsfpcibasic2 55952 0
hsfserial 23332 4
hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2
hsfengine 1203364 1 hsfserial
hsfosspec 100320 9
hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2,hsfserial,hsfengine
hsfsoar 52224 4
hsfmc97ali,hsfmc97via,hsfmc97ich,hsfpcibasic2
dm_mod 47317 0
button 4825 0
battery 7117 0
asus_acpi 9177 0
ac 3533 0
ext3 96937 1
jbd 66521 1 ext3
------------------------------------------------------------------------
lspci
00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
00:0a.0 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
00:0a.1 CardBus bridge: O2 Micro, Inc. OZ6933 Cardbus Controller (rev 01)
00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21
IEEE-1394a-2000 Controller (PHY/Link)
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 23)
00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 23)
00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 23)
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 30)
00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97
Modem] (rev 70)
01:00.0 VGA compatible controller: S3 Inc. VT8375 [ProSavage8 KM266/KL266]
------------------------------------------------------------------------
cat /proc/interrupts
CPU0 0: 4816547 XT-PIC timer
1: 6850 XT-PIC i8042
2: 0 XT-PIC cascade
3: 5638 XT-PIC eth0
8: 1 XT-PIC rtc
9: 60 XT-PIC acpi
10: 217490 XT-PIC hsfmc97via, VIA8233
12: 340675 XT-PIC i8042
14: 33196 XT-PIC ide0
15: 24 XT-PIC ide1
NMI: 0 ERR: 1
------------------------------------------------------------------------
cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000cdfff : Video ROM
000e0000-000e17ff : Adapter ROM
000f0000-000fffff : System ROM
00100000-0efeffff : System RAM
00100000-002f6fff : Kernel code
002f7000-00399bff : Kernel data
0eff0000-0effffbf : ACPI Tables
0effffc0-0effffff : ACPI Non-volatile Storage
10000000-10000fff : 0000:00:0a.0
10001000-10001fff : 0000:00:0a.1
90000000-9fffffff : PCI Bus #01
90000000-97ffffff : 0000:01:00.0
a0000000-a3ffffff : 0000:00:00.0
e0000000-efffffff : PCI Bus #01
e0000000-e007ffff : 0000:01:00.0
f0000000-f00007ff : 0000:00:0c.0
f0004000-f0007fff : 0000:00:0c.0
f0008000-f00080ff : 0000:00:0d.0
f0008000-f00080ff : 8139too
fff80000-ffffffff : reserved
------------------------------------------------------------------------
cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1008-100b : ACPI timer
1010-1015 : ACPI CPU throttle
1100-110f : 0000:00:11.1
1100-1107 : ide0
1108-110f : ide1
1200-121f : 0000:00:11.2
1300-131f : 0000:00:11.3
1700-171f : 0000:00:11.4
c000-dfff : PCI Bus #01
e000-e0ff : 0000:00:0d.0
e000-e0ff : 8139too
e100-e1ff : 0000:00:11.5
e100-e1ff : VIA8233
e200-e2ff : 0000:00:11.6
e200-e2ff : hsfmc97via
Další informace o konferenci Linux