Kompilace jadra a ATI
foul imp
foul_imp na swissinfo.org
Středa Září 22 09:41:52 CEST 2004
TAk jsem to prekompiloval znova a pres dmesg jsem vyjel starttovaci
"log" zde jsou. U noveho jadra nikde nevidim nejakou zminku o gr. karte,
nemuze to byt tim, ze jsem ovladace volil jako modul?
Lubos
>
>
------------- další část ---------------
Linux version 2.6.8.1 (root na darkstar) (gcc version 3.3.4) #1 Tue Sep 21 21:49:41 CEST 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000002000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
32MB LOWMEM available.
On node 0 totalpages: 8192
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4096 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
DMI 2.0 present.
ACPI disabled because your bios is from 97 and too old
You can enable it with acpi=force
Built 1 zonelists
Kernel command line: BOOT_IMAGE=Linux-2.6.8.1 ro root=301
Initializing CPU#0
CPU 0 irqstacks, hard=c0497000 soft=c0496000
PID hash table entries: 256 (order 8: 2048 bytes)
Detected 233.931 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 28160k/32768k available (2475k kernel code, 4176k reserved, 1033k data, 136k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 459.77 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 008001bf 00000000 00000000 00000000
CPU: After vendor identify, caps: 008001bf 00000000 00000000 00000000
Intel Pentium with F0 0F bug - workaround enabled.
CPU: After all inits, caps: 008001bf 00000000 00000000 00000000
CPU: Intel Pentium MMX stepping 03
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb120, last bus=0
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/0585] at 0000:00:00.0
audit: initializing netlink socket (disabled)
audit(1095805135.150:0): initialized
Installing knfsd (copyright (C) 1996 okir na monad.swb.de).
udf: registering filesystem
Activating ISA DMA hang workarounds.
lp: driver loaded but no devices found
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 [PCSPP(,...)]
lp0: using parport0 (polling).
Using anticipatory io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: WDC AC1210F, ATA DISK drive
hdb: WDC AC22500L, ATA DISK drive
hdc: CD-540E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 415380 sectors (212 MB) w/64KiB Cache, CHS=989/12/35
hda: hda1
hdb: max request size: 128KiB
hdb: 4999680 sectors (2559 MB) w/256KiB Cache, CHS=4960/16/63
hdb: hdb1 hdb2 < hdb5 >
hdc: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.02 loaded.
USB Universal Host Controller Interface driver v2.2
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
Advanced Linux Sound Architecture Driver Version 1.0.4 (Mon May 17 14:31:44 2004 UTC).
ALSA device list:
No soundcards found.
oprofile: using timer interrupt.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (256 buckets, 2048 max) - 296 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost na snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 136k freed
Adding 350744k swap on /dev/hdb5. Priority:-1 extents:1
8139too Fast Ethernet driver 0.9.27
eth0: RealTek RTL8139 at 0x6200, 00:30:4f:17:31:0b, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
spurious 8259A interrupt: IRQ7.
------------- další část ---------------
Linux version 2.4.26 (root na tree) (gcc version 3.3.4) #6 Mon Jun 14 19:07:27 PDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000002000000 (usable)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
32MB LOWMEM available.
On node 0 totalpages: 8192
zone(0): 4096 pages.
zone(1): 4096 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux-2.4.22 ro root=301
Initializing CPU#0
Detected 233.869 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 466.94 BogoMIPS
Memory: 29168k/32768k available (1844k kernel code, 3216k reserved, 618k data, 120k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Intel Pentium with F0 0F bug - workaround enabled.
CPU: After generic, caps: 008001bf 00000000 00000000 00000000
CPU: Common caps: 008001bf 00000000 00000000 00000000
CPU: Intel Pentium MMX stepping 03
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch na atnf.csiro.au)
mtrr: detected mtrr type: none
PCI: PCI BIOS revision 2.10 entry at 0xfb120, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/0585] at 00:00.0
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xe1000000, mapped to 0xc280d000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:4710
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Detected PS/2 Mouse Port.
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586a (rev 25) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0x6000-0x6007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x6008-0x600f, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC1210F, ATA DISK drive
hdb: WDC AC22500L, ATA DISK drive
hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hda: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0: Drive 0 didn't accept speed setting. Oh, well.
hda: set_drive_speed_status: status=0x51 { DriveReady SeekComplete Error }
hda: set_drive_speed_status: error=0x04 { DriveStatusError }
ide0: Drive 0 didn't accept speed setting. Oh, well.
blk: queue c03b3360, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03b349c, I/O limit 4095Mb (mask 0xffffffff)
hdc: CD-540E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 415380 sectors (213 MB) w/64KiB Cache, CHS=989/12/35
hdb: attached ide-disk driver.
hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: task_no_data_intr: error=0x04 { DriveStatusError }
hdb: 4999680 sectors (2560 MB) w/256KiB Cache, CHS=620/128/63, UDMA(33)
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1
hdb: hdb1 hdb2 < hdb5 >
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 254.400 MB/sec
32regs : 194.800 MB/sec
pII_mmx : 350.800 MB/sec
p5_mmx : 413.200 MB/sec
raid5: using function: p5_mmx (413.200 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.8(17/11/2003)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding Swap: 350744k swap-space (priority -1)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 4M
agpgart: no supported devices found.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Intel ISA PCIC probe: not found.
Databook TCIC-2 PCMCIA probe: not found.
ds: no socket drivers loaded!
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 at 0xc2b91000, 00:30:4f:17:31:0b, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-uhci.c: $Revision: 1.275 $ time 17:55:05 Jun 13 2004
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
UMSDOS 0.86k (compatibility level 0.4, fast msdos)
UMSDOS 0.86k (compatibility level 0.4, fast msdos)
UMSDOS_notify_change: //neco not in EMD, ret=-2
UMSDOS_notify_change: //neco not in EMD, ret=-2
UMSDOS_notify_change: //neco not in EMD, ret=-2
UMSDOS_notify_change: //neco not in EMD, ret=-2
UMSDOS_notify_change: //neco not in EMD, ret=-2
UMSDOS_notify_change: //neco not in EMD, ret=-2
UMSDOS_notify_change: //neco not in EMD, ret=-2
Další informace o konferenci Linux