odchazejici disk? - delsi
JaFi
newsy na filja.com
Pondělí Červen 13 18:52:16 CEST 2005
Vaclav Bilek napsal(a):
> doporucuji
>
> 1.smartctl -t long /dev/hda
> 2.vymenit ksandu
> pravdepodobne jde o vadny disk...
>
tak jsem ten test pustil a po jeho ukonceni jsem pouzil tento prikaz:
smartctl -a /dev/hda
smartctl version 5.21 Copyright (C) 2002-3 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD800JB-00CRA1
Serial Number: WD-WCA8E7531992
Firmware Version: 17.07W17
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Jun 13 18:42:02 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x85) Offline data collection activity was
aborted by an interrupting
command from host.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: (3120) seconds.
Offline data collection
capabilities: (0x3b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0007 103 094 021 Pre-fail
Always - 3941
4 Start_Stop_Count 0x0032 100 100 040 Old_age
Always - 127
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail
Always - 0
9 Power_On_Hours 0x0032 078 078 000 Old_age
Always - 16451
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 108
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always
- 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail
Offline - 0
SMART Error Log Version: 1
ATA Error Count: 17 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Timestamp = decimal seconds since the previous disk power-on.
Note: timestamp "wraps" after 2^32 msec = 49.710 days.
Error 17 occurred at disk power-on lifetime: 13 hours
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 80 2a cc 17 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
c8 00 80 26 cc 17 e0 00 102.100 READ DMA
c8 00 88 1e cc 17 e0 00 99.450 READ DMA
c8 00 90 16 cc 17 e0 00 96.850 READ DMA
c8 00 98 0e cc 17 e0 00 94.400 READ DMA
c8 00 a0 06 cc 17 e0 00 91.900 READ DMA
Error 16 occurred at disk power-on lifetime: 13 hours
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 88 2a cc 17 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
c8 00 88 1e cc 17 e0 00 99.450 READ DMA
c8 00 90 16 cc 17 e0 00 96.850 READ DMA
c8 00 98 0e cc 17 e0 00 94.400 READ DMA
c8 00 a0 06 cc 17 e0 00 91.900 READ DMA
c8 00 a8 fe cb 17 e0 00 89.400 READ DMA
Error 15 occurred at disk power-on lifetime: 13 hours
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 90 2a cc 17 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
c8 00 90 16 cc 17 e0 00 96.850 READ DMA
c8 00 98 0e cc 17 e0 00 94.400 READ DMA
c8 00 a0 06 cc 17 e0 00 91.900 READ DMA
c8 00 a8 fe cb 17 e0 00 89.400 READ DMA
c8 00 b0 f6 cb 17 e0 00 86.800 READ DMA
Error 14 occurred at disk power-on lifetime: 13 hours
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 98 2a cc 17 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
c8 00 98 0e cc 17 e0 00 94.400 READ DMA
c8 00 a0 06 cc 17 e0 00 91.900 READ DMA
c8 00 a8 fe cb 17 e0 00 89.400 READ DMA
c8 00 b0 f6 cb 17 e0 00 86.800 READ DMA
c8 00 b8 ee cb 17 e0 00 84.300 READ DMA
Error 13 occurred at disk power-on lifetime: 13 hours
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 a0 2a cc 17 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Timestamp Command/Feature_Name
-- -- -- -- -- -- -- -- --------- --------------------
c8 00 a0 06 cc 17 e0 00 91.900 READ DMA
c8 00 a8 fe cb 17 e0 00 89.400 READ DMA
c8 00 b0 f6 cb 17 e0 00 86.800 READ DMA
c8 00 b8 ee cb 17 e0 00 84.300 READ DMA
c8 00 c0 e6 cb 17 e0 00 81.700 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 66
-
Zde na konci je videt, ze test skoncil bez chyb. Kazdopadne jsou mi
divne ty hlasky Error 13 apod. Nevim, co znamenaji. Kdyz totiz dam
smartctl -a /dev/hdc , tak tam tyto hlasky nejsou. Vypis je takovyto:
smartctl version 5.21 Copyright (C) 2002-3 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD800JB-00CRA1
Serial Number: WD-WCA8E7531306
Firmware Version: 17.07W17
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Jun 13 18:47:13 2005 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity was
completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 248) Self-test routine in progress...
80% of test remaining.
Total time to complete Offline
data collection: (3120) seconds.
Offline data collection
capabilities: (0x3b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0007 097 095 021 Pre-fail
Always - 4233
4 Start_Stop_Count 0x0032 100 100 040 Old_age
Always - 249
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail
Always - 0
9 Power_On_Hours 0x0032 081 081 000 Old_age
Always - 14512
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 165
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always
- 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always
- 1
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [Use the smartctl -t option to run these.]
Myslite, ze je tedy problem v kablu? To se mi moc nezda. Ten server uz
bezi 2 roky a zatim s nim zadny problem neni. Bohuzel je na druhem konci
republiky, tak nejsem schopen ZKUSIT vymenu kabelu ani disku. A nez se k
nemu vydam, rad bych zjistil, v cem je problem ... abych jel na jistotu.
Ale je pravda, ze od toho problemu se server chova nejak divne. Obcas
nejsou dostupne nejake sluzby apod. Vzdy jenom na chvili.
Jeste se zeptam ... muzu na ten disk pouzit prikaz badblocks , kdyz je v
poli? Neposkodim si tim to pole?
Diky
Jarda F.
Další informace o konferenci Linux