problém hostap_pci.ko

[Stanislav Mařík]

Michal Schmidt napsal(a):
> Stanislav Mařík wrote:
> 
>> FATAL: Error inserting hostap_pci 
>> (/lib/modules/2.6.14-hardened-r7/net/hostap_pci.ko): Unknown symbol in 
>> module, or unknown parameter (see dmesg)
> 
> 
> A podíval jste se do toho výpisu dmesg?
> 

Bohužel tam nic nevidím. Dmesg přikládám.
Standa

Linux version 2.6.14-hardened-r7 (root na router) (gcc version 3.3.6 
(Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #1 SMP Wed Apr 26 12:35:52 
CEST 2006
BIOS-provided physical RAM map:
  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
  BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
  BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
  BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
   DMA zone: 4096 pages, LIFO batch:1
   Normal zone: 126960 pages, LIFO batch:31
   HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 IntelR                                ) @ 0x000f74d0
ACPI: RSDT (v001 IntelR MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 IntelR MSI ACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 
real_root=/dev/hda3 vga=791 splash=verbose udev
bootsplash: verbose mode.
Found and enabled local APIC!
mapped APIC to ffffd000 (fee00000)
Initializing CPU#0
CPU 0 irqstacks, hard=c0489000 soft=c0481000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1205.921 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 512384k/524224k available (2437k kernel code, 11252k reserved, 
492k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2413.92 BogoMIPS 
(lpj=4827844)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff 00000000 00000000 00000000 
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff 00000000 00000000 00000000 
00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040 00000000 
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 08a8)
CPU0: Intel(R) Pentium(R) III CPU             1200MHz stepping 01
SMP motherboard not detected.
Brought up 1 CPUs
checking if image is initramfs...it isn't (no cpio magic); looks like an 
initrd
softlockup thread 0 started up.
Freeing initrd memory: 2137k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 4000-407f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 4080-40bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
report
TC classifier action (bugs to netdev na vger.kernel.org cc hadi na cyberus.ca)
PCI: Bridge: 0000:00:01.0
   IO window: 9000-9fff
   MEM window: d4000000-d7ffffff
   PREFETCH window: d8000000-d9ffffff
PCI: Bridge: 0000:00:1e.0
   IO window: a000-afff
   MEM window: da000000-dbffffff
   PREFETCH window: dc000000-dc0fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
audit: initializing netlink socket (disabled)
audit(1146089465.776:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, 
no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
vesafb: framebuffer at 0xd8000000, mapped to 0xe0880000, using 6144k, 
total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:8411
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
vesafb: Mode is VGA compatible
bootsplash: scanning last 2MB of initrd for signature
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 
21768 bytes,<6>...found (1024x768, 20089 bytes, v3).
Console: switching to colour frame buffer device 122x40
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 17
ICH2: not 100% native mode: will probe irqs later
     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
     ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD600JB-00CRA1, ATA DISK drive
hdb: WDC WD800JB-00FMA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST380011A, ATA DISK drive
hdd: ST3160021A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 117231408 sectors (60022 MB) w/8192KiB Cache, CHS=65535/16/63, 
UDMA(100)
hda: cache flushes not supported
  hda: hda1 hda2 hda3 hda4
hdb: max request size: 128KiB
hdb: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, 
UDMA(100)
hdb: cache flushes supported
  hdb: hdb1
hdc: max request size: 1024KiB
hdc: Host Protected Area detected.
	current capacity is 156299375 sectors (80025 MB)
	native  capacity is 156301488 sectors (80026 MB)
hdc: Host Protected Area disabled.
hdc: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, 
UDMA(100)
hdc: cache flushes supported
  hdc: hdc1
hdd: max request size: 1024KiB
hdd: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, 
UDMA(100)
hdd: cache flushes supported
  hdd: hdd1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.39
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 204k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v2.3
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1306 $ Ben Collins <bcollins na debian.org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 1.12 loaded.
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel na redhat.com
ReiserFS: hda3: warning: sh-2021: reiserfs_fill_super: can not find 
reiserfs on hda3
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 977248k swap on /dev/hda2.  Priority:-1 extents:1 across:977248k
EXT3 FS on hda3, internal journal
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 11 (level, 
low) -> IRQ 11
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
         <Adaptec 2940 Ultra SCSI adapter>
         aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs

   Vendor: COMPAQ    Model: BB009235B6        Rev: B013
   Type:   Direct-Access                      ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled.  Depth 32
  target0:0:0: Beginning Domain Validation
  target0:0:0: wide asynchronous.
  target0:0:0: Domain Validation skipping write tests
  target0:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 8)
  target0:0:0: Ending Domain Validation
SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB)
SCSI device sda: drive cache: write through
  sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
   Vendor: IBM-PSG   Model: DDYS-T18350N  M   Rev: S9HA
   Type:   Direct-Access                      ANSI SCSI revision: 03
scsi0:A:4:0: Tagged Queuing enabled.  Depth 32
  target0:0:4: Beginning Domain Validation
  target0:0:4: wide asynchronous.
  target0:0:4: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 8)
  target0:0:4: Ending Domain Validation
SCSI device sdb: 35548320 512-byte hdwr sectors (18201 MB)
SCSI device sdb: drive cache: write through
SCSI device sdb: 35548320 512-byte hdwr sectors (18201 MB)
SCSI device sdb: drive cache: write through
  sdb: sdb1
Attached scsi disk sdb at scsi0, channel 0, id 4, lun 0
   Vendor: COMPAQ    Model: SDT-9000          Rev: 4.05
   Type:   Sequential-Access                  ANSI SCSI revision: 02
  target0:0:6: Beginning Domain Validation
  target0:0:6: Domain Validation skipping write tests
  target0:0:6: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
  target0:0:6: Ending Domain Validation
st: Version 20050830, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi0, channel 0, id 6, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 
1048575
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKD] -> GSI 7 (level, low) 
-> IRQ 7
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:03.0: 3Com PCI 3c905C Tornado at 0xa400. Vers LK1.1.19
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 5 (level, low) 
-> IRQ 5
eth1: RealTek RTL8139 at 0xe1158000, 00:50:fc:23:64:d1, IRQ 5
eth1:  Identified 8139 chip type 'RTL-8139C'
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12