XWindows & karta

[Vladimir Trestik]

Ahoj vsichni

mam tu takovy problem: po spravnem nakonfigurovani xf86configu pro grafickou kartu miro VIDEO 40SV ergo 
(S3-968) a monitoru (jeho frekvenci) mi po spusteni Xwindows jde monitor do power savingu, i kdyz prepinam 
ctrl+alt++.

V textovym okne mi to vypise toto:

Operating System: Linux
Configured drivers:
  S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
      mmio_928, s3_generic
(using VT number 7)

XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) Mouse: type: MouseSystems, device: /dev/mouse, baudrate: 1200
(**) S3: Graphics device ID: "card-miro"
(**) S3: Monitor ID: "monitor-miro"
(--) S3: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(--) S3: card type: PCI
(--) S3: chipset:   968 rev. 31
(--) S3: chipset driver: mmio_928
(**) S3: videoram:  4096k
(**) S3: Ramdac type: ti3026
(--) S3: Ramdac speed: 135
(--) S3: Using hardware cursor from Ti3026 RAMDAC
(**) S3: Using TI 3026 programmable clock (MCLK 54.982 MHz)
(--) S3: Maximum allowed dot-clock: 135.000 MHz
(**) S3: Mode "1280x1024": mode clock =  80.000
(**) S3: Mode "1024x768": mode clock =  85.000
(**) S3: Mode "800x600": mode clock =  50.000
(**) S3: Mode "640x480": mode clock =  31.500
(**) S3: Mode "640x400": mode clock =  25.175
(**) S3: Mode "400x300": mode clock =  25.000
(**) S3: Mode "320x240": mode clock =  15.750
(**) S3: Mode "320x200": mode clock =  12.588
(--) S3: Operating RAMDAC in pixel multiplex mode
(--) S3: Using 8 bits per RGB value
(**) S3: Virtual resolution set to 1600x1280
(--) S3: Ti3026 hardware cursor in interlaced modes doesn't work correctly,
        please use Option "no_ti3026_curs" when using interlaced modes!
(--) S3: Local bus LAW is 0xF3000000
(--) S3: Using a banksize of 4096k, line width of 1600
(--) S3: Using a single 64x64 area at (1536,1280) for expanding pixmaps
(--) S3: Using 8 planes of 1536x1341 at (0,1280) aligned 8 as font cache
(--) S3: Specified dot clock (12.588) too low for TI 3026(--)


Diky za kazdou odpoved, jak tento problem vyresit.