Xka: Unwilling manager (krapitek delsi)

Zuber Martin zuber na kotr23.ost.skoda.cz
Středa Květen 19 12:38:27 CEST 1999


	Dobry den,
stala se nam na jednom pocitaci divna vec. Mame tu nekolik linuxu pripojenych na 
HP stanice. Az na jeden, ktery se nam nechce pripojit. Toto hlaseni jsem nikde 
nevidel, tak ze jsem ulovil cely vypis pri nabehu X.

Udaje o PC: Linux RH 5.2, cerstve nainstalovany z Infomagicu, P133, NE2000, S3 
Trio karta (ta bezi).

Pripoji se nam to pouze na server (tez HP). HP jsou HP 9000, HP-UX 10.20. 
Zkousel jsem to na stanicich kam se 100% pripojim (jinak bych nenapsal tenhle 
mailik).

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ V Y P I S ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


XFree86 Version 3.3.2.3 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: July 15 1998
        If the server is older than 6-12 months, or if your card is newer
        than the above date, look for a newer version before reporting
        problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.34 i686 [ELF] 
Configured drivers:
  S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
      newmmio, mmio_928, s3_generic
(using VT number 8)

XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keycodes: "xfree86"
(**) XKB: types: "default"
(**) XKB: compat: "default"
(**) XKB: symbols: "us(pc101)"
(**) XKB: geometry: "pc"
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc101"
(**) XKB: layout: "us"
(**) Mouse: type: Microsoft, device: /dev/mouse, baudrate: 1200
(**) Mouse: buttons: 3
(**) S3: Graphics device ID: "My Video Card"
(**) S3: Monitor ID: "Generic Monitor"
(--) S3: Mode "640x400" needs vert refresh rate of 69.93 Hz. Deleted.
(--) S3: Mode "800x600" needs hsync freq of 35.16 kHz. Deleted.
(--) S3: Mode "640x480" needs hsync freq of 36.46 kHz. Deleted.
(--) S3: Mode "800x600" needs hsync freq of 37.88 kHz. Deleted.
(--) S3: Mode "800x600" needs hsync freq of 48.08 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 48.36 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted.
(--) S3: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) S3: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) S3: Mode "320x200" needs vert refresh rate of 69.93 Hz. Deleted.
(--) S3: Mode "320x240" needs hsync freq of 39.38 kHz. Deleted.
(--) S3: Invalid vertical timing for mode "400x300". Deleted.
(--) S3: Mode "400x300" needs hsync freq of 37.88 kHz. Deleted.
(--) S3: Mode "400x300" needs hsync freq of 48.08 kHz. Deleted.
(--) S3: Mode "480x300" needs hsync freq of 35.16 kHz. Deleted.
(--) S3: Mode "480x300" needs hsync freq of 37.80 kHz. Deleted.
(--) S3: Mode "480x300" needs hsync freq of 39.56 kHz. Deleted.
(--) S3: Mode "480x300" needs hsync freq of 48.00 kHz. Deleted.
(--) FontPath set to "tcp/ser1:7000"
(--) S3: PCI: Trio32/64 rev 54, Linear FB @ 0xe0000000
(--) S3: chipset:   Trio64V+ rev. 54
(--) S3: chipset driver: newmmio
(--) S3: card type: PCI
(--) S3: videoram:  1024k
(--) S3: Ramdac type: s3_trio64
(--) S3: Ramdac speed: 135 MHz
(--) S3: Using Trio32/64 programmable clock (MCLK 59.957 MHz)
(--) S3: Maximum allowed dot-clock: 135.000 MHz
(**) S3: Mode "640x480": mode clock =  25.175
(--) S3: There is no mode definition named "800x600"
(--) S3: Removing mode "800x600" from list of valid modes.
(--) S3: Using 6 bits per RGB value
(--) S3: Virtual resolution set to 640x480
(--) S3: Local bus LAW is 0xE0000000
(--) S3: Using a banksize of 1024k, line width of 640
(--) S3: Using a single 64x64 area at (576,482) for expanding pixmaps
(--) S3: Using 8 planes of 640x1092 at (0,546) aligned 8 as font cache

Fatal server error:
XDMCP fatal error: Manager unwilling Host unwilling


When reporting a problem related to a server crash, please send
the full server output, not just the last messages

~~~~~~~~~~~~~~~~~~~~~~~~~ K O N E C   V Y P I S U ~~~~~~~~~~~~~~~~~~~~~~~~~~~

Diky za kazdou rozumnou radu.

						Martin Zuber


Další informace o konferenci Linux