PCMCIA BreezeCOM SA PCR-11 Pro

[Petr Kadlec]

On Sat, 16 Jun 2001 istenp2.epr na mail.cez.cz wrote:

>
> Zdravim.
>
> Pokousim se rozchodit kartu BreezeCOM SA PCR-11 Pro. Bohuzel at se snazim,
> jak chci, stale se nedari.
> Vyzkousel jsem uz RH6.1cz, RH7.0cz, RH7.1cz a stale nic. Pod RH7.1cz
> (kernel 2.4.2) se mi zatim nepodarilo ani zkompilovat driver.
> Karta se zinicializuje a tvari se funkcne, sitovy interface najede, ale na
> karte nesviti ani jedna dioda a karta nefunguje...
>
> Proto Vas nekoho, komu to funguje moc prosim: !!! PORADTE !!!
> Nebo alespon doporucte chodivou distribuci+chodive jadro+chodive
> pcmcia-cs.
>
> dik za jakoukoliv pomoc, uz jsem celkem zoufaly...
>
> Toto jsou zaznamy z logu RH7.0cz (na RH6.1cz se to chovalo uplne stejne):
>
> kernel: Linux PCMCIA Card Services 3.1.19
> kernel:   kernel build: 2.2.16-22 #1 Tue Aug 22 15:48:40 EDT 2000
> kernel:   options:  [pci] [cardbus] [apm]
> kernel: Intel PCIC probe:
> kernel:   Vadem VG-469 rev 00 ISA-to-PCMCIA at port 0x3e0 ofs 0x00
> kernel:     host opts [0]: none
> kernel:     host opts [1]: none
> kernel:     ISA irqs (scanned) = 3,4,5,7,11,12 status change on irq 11
> rc: Starting pcmcia:  succeeded
> cardmgr[428]: starting, version is 3.1.19
> cardmgr[428]: watching 2 sockets
> kernel: cs: IO port probe 0x1000-0x17ff: excluding 0x12f8-0x12ff
> 0x1378-0x137f 0x13f0-0x13ff 0x16f8-0x16ff 0x1778-0x177f 0x17f0-0x17ff
> kernel: cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
> cardmgr[428]: initializing socket 0
> kernel: cs: memory probe 0x0d0000-0x0dffff: clean.
> cardmgr[428]: socket 0: BreezeCOM SA PCR-11 Pro
> cardmgr[428]: executing: 'modprobe xbrzcom_cs ess_id=xxx verbose=1'
> kernel: BreezeNet Pro.11 SA-PCR --- BreezeCOM Linux Driver Version 1.0
> kernel: BreezeNet Pro.11 SA-PCR ==> Attaching...
> kernel: BreezeNet Pro.11 SA-PCR ==> Event: Card Insertion
> kernel: BreezeNet Pro.11 SA-PCR ==> Configuring...
> kernel: BreezeNet Pro.11 SA-PCR ==> Hardware Reset
> kernel: BreezeNet Pro.11 SA-PCR ==> Requesting IRQ 5 (returned 0)
> kernel: BreezeNet Pro.11 SA-PCR ==> NET ERROR
> kernel: BreezeNet Pro.11 SA-PCR ==> Configuration done
> kernel: BreezeNet Pro.11 SA-PCR ==> Initialized
> kernel: BreezeNet Pro.11 SA-PCR ==> Attached
> cardmgr[428]: executing: './network start eth2'

tady prece sam vidite hlaseni o chybe, bud to mate nekde spatne nastavene,
nebo nemate volne IRQ 5, tzn. prohlednete si /etc/pcmcia/network.opts
(resp. dle vasi distribuce a verze pcmcia), pripadne si zkuste vyhradit
IRQ 5 v nastraveni BIOSu...


-- 

	Petr Kadlec

           <=== GIN ISP: http://www.gin.cz, email: kadlec na gin.cz ===>
    <=== Personal: http://www.krakenuv.net, email: kraken na krakenuv.net ===>