karta Nvidia pri vyuziti GLX zpusobi zatuhnuti PC - long
Kuffa Libor
libor.kuffa na logit.cz
Pondělí Květen 13 10:03:14 CEST 2002
Hezky den,
mam dele trvajici problem s kartou (ci spise obecne s kartami) Nvidia pod
LINUXem - jakmile se pokusim spustit cokoli, co vyuziva 3D funkce - setric
obrazovky, hru, popripade pouze glxgears, pocitac behem 2-8 vterin kompletne
zatuhne - nejde ani ping z jiného stroje, mys a klavesnice jsou zablokovane,
atd. Pomaha pouze HW reset :-((. Ve W2k prof. karty chodi relativne dobre,
Quake, Rally 2000, Black and White, atp. celkem bez problemu, jednou za
tyden BSOD.
Puvodne jsem mel v pocitaci kartu Manli Nvidia MX200/32MB RAM a mel jsem
tendenci to svadet na HW problem (se kterym se Winy jakz takz vyrovnaly a
LINUX ne). Nyni se mi naskytla sance a vymenil jsem ji za Nvidia Vanta TNT2
64 AGP/32MB RAM - a problem zustal, coz mne docela mrzi.
Zkousel jsem vsechny varianty ovladacu od Nvidie, ktere se mi podarilo
sehnat a zkousel jsem je jak z RPM baliku, tak kompilovat, vysledek je porad
stejny - modul NVdriver se zavede a vsechno v X-ech chodi (divx filmy,
vyhlazovani pisem, atd.) - az do pokusu o vyuziti 3D funkci.
Pouzivam Mandrake 8.2 + KDE3, ale stejny problem mam i s WMaker-em (a jak uz
jsem psal, problem je dele trvajici a mel jsem jej i na RH 6.2).
Obracim se tedy s prosbou o radu na sirsi komunitu - posilam vypis lspci
-vv, vypis glxinfo, vypis z XF86Config-4 a popis HW meho pocitace. K
XF86Config-4 - Nektere radky v sekci "Device" jsou zakomentovany, ale
ujistuji vas, ze kdyz je odkomentuji, chova se to stejne.
Diky moc za jakekoli nasmerovani - protoze se jedna o domaci PC, podrobnejsi
odpovedi na vase pripadne otazky budou az zitra.
Libor Kuffa
HW:
MB: Jetway J542-B
Chipset: Ali 1541
RAM: 192 MB, DIMM
procesor: AMD K6-2/450MHz
Vypis XF86Config-4
----------------------------
Section "Module"
# This loads the DBE extension module.
Load "dbe"
# Load "dri"
Load "glx"
# Load "GLcore"
Load "extmod"
# This loads the Video for Linux module.
Load "v4l"
SubSection "extmod"
#Option "omit xfree86-dga"
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"
Section "Device"
Identifier "NVIDIA GeForce2 DDR (generic)"
VendorName "nvidia"
BoardName "Unknown"
Driver "nvidia"
# BusID "PCI:1:0:0"
# VideoRam 32768
# Clock lines
# Uncomment following option if you see a big white block
# instead of the cursor!
# Option "sw_cursor"
Option "DPMS" "on"
# Option "NvAGP" "1"
EndSection
Vypis glxinfo:
-------------------
name of display: :0.0
display: :0 screen: 0
direct rendering: Yes
server glx vendor string: NVIDIA Corporation
server glx version string: 1.2
server glx extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_SGIX_fbconfig,
GLX_SGIX_pbuffer
client glx vendor string: NVIDIA Corporation
client glx version string: 1.2
client glx extensions:
GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_EXT_visual_info,
GLX_EXT_visual_rating, GLX_EXT_import_context, GLX_SGI_video_sync,
GLX_SGIX_swap_group, GLX_SGIX_swap_barrier, GLX_SGIX_fbconfig,
GLX_SGIX_pbuffer
GLX extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_SGIX_fbconfig,
GLX_SGIX_pbuffer, GLX_ARB_get_proc_address
OpenGL vendor string: NVIDIA Corporation
OpenGL renderer string: RIVA TNT2/AGP/3DNOW!
OpenGL version string: 1.3.1 NVIDIA 28.02
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_texture_env_add,
GL_ARB_transpose_matrix, GL_EXT_abgr, GL_EXT_bgra,
GL_EXT_compiled_vertex_array, GL_EXT_draw_range_elements,
GL_EXT_fog_coord, GL_EXT_multi_draw_arrays, GL_EXT_packed_pixels,
GL_EXT_point_parameters, GL_EXT_rescale_normal, GL_EXT_secondary_color,
GL_EXT_separate_specular_color, GL_EXT_stencil_wrap,
GL_EXT_texture_edge_clamp, GL_EXT_texture_env_add,
GL_EXT_texture_env_combine, GL_EXT_texture_lod_bias,
GL_EXT_texture_object, GL_EXT_vertex_array, GL_EXT_vertex_weighting,
GL_IBM_texture_mirrored_repeat, GL_KTX_buffer_region,
GL_NV_blend_square,
GL_NV_evaluators, GL_NV_fog_distance, GL_NV_packed_depth_stencil,
GL_NV_texgen_reflection, GL_NV_texture_env_combine4,
GL_SGIS_multitexture
glu version: 1.3
glu extensions:
GLU_EXT_nurbs_tessellator, GLU_EXT_object_space_tess
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
----------------------------------------------------------------------
0x21 16 tc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 16 0 0 None
0x22 16 dc 0 16 0 r y . 5 6 5 0 0 16 0 16 16 16 16 0 0 None
0x23 16 tc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 16 0 0 None
0x24 16 dc 0 16 0 r . . 5 6 5 0 0 16 0 16 16 16 16 0 0 None
Vypis lspci -vv:
----------------------
00:00.0 Host bridge: Acer Laboratories Inc. [ALi] M1541 (rev 04)
Subsystem: Acer Laboratories Inc. [ALi] ALI M1541 Aladdin V/V+ AGP
System Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [b0] AGP version 1.0
Status: RQ=27 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Acer Laboratories Inc. [ALi] M5243 (rev 04) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: d2000000-d3ffffff
Prefetchable memory behind bridge: d0000000-d1ffffff
BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge
[Aladdin IV] (rev c3)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort+ <MAbort+ >SERR- <PERR-
Latency: 0
00:08.0 Communication controller: Lucent Microelectronics 56k WinModem (rev
01)
Subsystem: Lucent Microelectronics LT WinModem 56k
Data+Fax+Voice+VoiceView+Dsvd
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d5001000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 2000 [size=8]
Region 2: I/O ports at 2400 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 08)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at 2800 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 2c00 [size=32]
00:0f.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c1)
(prog-if fa)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 9
Region 4: I/O ports at 3000 [size=16]
01:00.0 VGA compatible controller: nVidia Corporation Vanta [NV6] (rev 15)
(prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Další informace o konferenci Linux