externi diskove pole

[Mošnička Roman]

> scsi1 : QLogic QLA2200 PCI to Fibre Channel Host Adapter: bus 1 device 5 irq 3
>         Firmware version:  2.01.38, Driver version 5.38.9-fo
> scsi: unknown type 12
>   Vendor: DEC       Model: HSG80CCL          Rev: V86F
>   Type:   Unknown                            ANSI SCSI revision: 02
> scsi(1:0:0:0): Enabled tagged queuing, queue depth 16.
> resize_dma_pool: unknown device type 12
> resize_dma_pool: unknown device type 12
>
> to mi nic nerika - mozna jsem ale slepej ....

>>No, podle me si to staci precist. Kernel najde scsi zarizeni, ovsem nezna
>>jeho typ, takze vam zadny disk nevyrobi. Nevim z hlavy, co je to "type 12",
>>ale ocekaval bych, ze diskove pole se bude tvarit jako disk. Pokud je tomu
>>tak, tak to zmamena asi tolik, ze mate sice driver k tomu poli, ale nemate
>>v kernelu zakompilovany driver pro scsi disk :-))

Tak nevim - vyzkousel jsem znova prekompilovat ovladac a po znovuzavedeni ovladace najednou vidim zarizeni ....
stejnej postup pri kompilaci ovladace, zavedeni - jedinej rozdil je ten, ze ted kdyz jsem ovladac kompilovat,
tak jsem mel ke karte pripojene diskove pole. Tim bych ale nerekl ze ta zmena k lepsimu bude :-)

Dekuji vsem za pomoc a preji pekny vecer
Roman Mosnicka


qla2x00: Found  VID=1077 DID=2200 SSVID=1077 SSDID=2
scsi1: Found a QLA2200  @ bus 1, device 0x5, irq 3, iobase 0xc400
scsi(1): Configure NVRAM parameters...
scsi(1): Verifying loaded RISC code...
scsi(1): Verifying chip...
scsi(1): LIP reset occurred
scsi(1): Waiting for LIP to complete...
scsi(1): LOOP UP detected
scsi1: Topology - (F_Port), Host Loop address 0xffff
scsi1: Topology - (F_Port), Host Loop address 0xffff
scsi-qla0-adapter-port=210000e08b069554\;
scsi-qla0-tgt-0-di-0-node=50001fe1000bfcf0\;
scsi-qla0-tgt-0-di-0-port=50001fe1000bfcf1\;
scsi-qla0-tgt-0-di-0-control=00\;
scsi-qla0-tgt-0-di-0-preferred=ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff\;
scsi-qla0-tgt-0-di-1-node=50001fe1000bfcf0\;
scsi-qla0-tgt-0-di-1-port=50001fe1000bfcf2\;
scsi-qla0-tgt-0-di-1-control=80\;
scsi1 : QLogic QLA2200 PCI to Fibre Channel Host Adapter: bus 1 device 5 irq 3
        Firmware version:  2.01.38, Driver version 5.38.9-fo
scsi: unknown type 12
  Vendor: DEC       Model: HSG80CCL          Rev: V86F
  Type:   Unknown                            ANSI SCSI revision: 02
  Vendor: DEC       Model: HSG80             Rev: V86F
  Type:   Direct-Access                      ANSI SCSI revision: 02
scsi(1:0:0:0): Enabled tagged queuing, queue depth 16.
scsi(1:0:0:1): Enabled tagged queuing, queue depth 16.
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0,  type 12
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 1
resize_dma_pool: unknown device type 12
SCSI device sdb: 711146230 512-byte hdwr sectors (364107 MB)
 sdb: sdb1 sdb2