HW problem: Dve sitovky

[Sniper_2]

> A samotne chodi? Rozhodne se nejdrive vydejte cestou modulu. Pak se
> podivejte jestli chudinky nesdili stejne irq ci io.
> 
> -- Dalibor Straka
V tom stroji jsou jen tri karty (z toho ty dve nejdou rozchodit) takze myslim ze ke konfliktu nedojde. 
Samostatne take nejdou. Jen pod Win :-)
Mezitim se mi podarilo jeste nejak rozchodit aspon toho 3coma s Tulip
driverem. Ale porad mi nejvic vadi ta Gbs sitovka.

0000:01:00.0 Ethernet controller: 3Com Corporation 3CSOHO100B-TX 910-A01 [tulip] (rev 31)
        Subsystem: 3Com Corporation 3CSOHO100B-TX 910-A01 [tulip]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (16000ns min, 32000ns max), cache line size 10
        Interrupt: pin A routed to IRQ 7
        Region 0: I/O ports at b800 [size=ff8c0000]
        Region 1: Memory at ff8ffc00 (32-bit, non-prefetchable) [size=1K]
        Expansion ROM at 00020000 [disabled]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:01.0 Ethernet controller: Sundance Technology Inc: Unknown device 1021 (rev 07)
        Subsystem: Sundance Technology Inc: Unknown device 5450
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (7500ns min, 15500ns max), cache line size 10
        Interrupt: pin A routed to IRQ 4
        Region 0: I/O ports at b400 [size=ff8e0000]
        Expansion ROM at 00008000 [disabled]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0000:01:08.0 Ethernet controller: Intel Corporation 82562EZ 10/100 Ethernet Controller (rev 01)
        Subsystem: Intel Corporation: Unknown device 304a
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2000ns min, 14000ns max), cache line size 10
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at ff8fe000 (32-bit, non-prefetchable)
        Region 1: I/O ports at bc00 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 PME-Enable+ DSel=0 DScale=2 PME-

# cat /proc/interrupts
           CPU0
  0:     151816          XT-PIC  timer
  2:          0          XT-PIC  cascade
  5:          0          XT-PIC  uhci_hcd
  7:          1          XT-PIC  eth1
  9:          3          XT-PIC  acpi, ehci_hcd
 10:       3264          XT-PIC  libata, uhci_hcd
 11:        910          XT-PIC  uhci_hcd, uhci_hcd, eth0
 14:        162          XT-PIC  ide0
 15:        111          XT-PIC  ide1
NMI:          0
ERR:          0