Stopování HW chyb - chipset, harddisk

n_petr na seznam.cz n_petr na seznam.cz
Středa Leden 25 02:00:33 CET 2006


S malinkou prodlevou zasílám výstup v příloze ze smartctl -a, smartctl 
-t long. Jestli jsem výstup dobře pochopil, tak by měl být disk v 
pořádku. Nebo které řádky konkrétně jsou nejdůležitější = na kterých se 
píše, zda je disk OK?

Jinak zatím pole drží. Myslím si, že se buď nesnášely 2 Seagate disky na 
jednom kabelu nebo 2 Seagate disky s rozdílnou cache na jednom kabelu či 
byl problém někde úplně jinde, ale to už nevím kde.

Asi to není úplně perfektní řešení, ale zatím pomáhá. Každopádně pokud 
budu stavět nějaké RAID pole, nedám do něho ani jeden Seagate disk 
(možná až v nové modelové řadě). Budu volit Western, Samsung, Hitachi; 
Maxtor (už asi ne, protože ho zkoupil Seagate)... no a jestli pak 
zjistím, že vypadávají z pole disky od stejného výrobce s různou cache, 
tak jsem Seagate zbytečně ukřivdil. Je jasné, že by měly být všechny 
disky identické, ale pokud se vám sejdou různé typy, tak co se dá dělat.

Děkuji, Petr Novák

Jan Kasprzak napsal(a):
> n_petr na seznam.cz wrote:
> : Ahoj,
> : co si myslíte o tomto logu z dmesg?
> : 
> : hdl: dma_timer_expiry: dma status == 0x61
> : hdl: DMA timeout error
> : hdl: dma timeout error: status=0xd0 { Busy }
> : hdk: DMA disabled
> : hdl: DMA disabled
> : hdl: status error: status=0x00 { }
> : hdl: drive not ready for command
> : hdl: status error: status=0x00 { }
> : hdl: drive not ready for command
> : hdl: status error: status=0x00 { }
> : hdl: drive not ready for command
> : hdl: status error: status=0x00 { }
> : hdl: drive not ready for command
> : end_request: I/O error, dev hdl, sector 305100095
> : raid5: Disk failure on hdl1, disabling device. Operation continuing on 7 
> : devices
> : end_request: I/O error, dev hdl, sector 305100103
> : end_request: I/O error, dev hdl, sector 305100111
> : end_request: I/O error, dev hdl, sector 305100119
> : .
> : .
> : .
> : 
> : Jedná se o RAID5 pole z 8 disků. Jeden disk jsem už vyměnil, SeaTools 
> : na něm našel chyby - ostatní disky byly OK. A teď zase podobná 
> : hláška a odstavení dalšího disku :-(. Dokonce jsem disky zapojil přes 
> : řadiče integrované na MSI desce a vyhodil Kouwelly z PCI.
>
> 	Ano, muze to byt vadny disk nebo radic nebo kabel. Co si
> o tom disku mysli "smartctl -a"? Pripadne "smartctl -t long"?
>
> -Y.
>   

------------- další část ---------------
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     ST3160021A
Serial Number:    3JS0LZ2J
Firmware Version: 3.06
User Capacity:    160,041,885,696 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Tue Jan 24 20:22:20 2006 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 ( 430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					No General Purpose Logging support.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 111) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   063   056   006    Pre-fail  Always       -       146619997
  3 Spin_Up_Time            0x0003   098   097   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       10
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   088   060   030    Pre-fail  Always       -       714226815
  9 Power_On_Hours          0x0032   088   088   000    Old_age   Always       -       10872
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       220
194 Temperature_Celsius     0x0022   037   049   000    Old_age   Always       -       37
195 Hardware_ECC_Recovered  0x001a   063   055   000    Old_age   Always       -       146619997
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   196   000    Old_age   Always       -       8
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 8 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 8 occurred at disk power-on lifetime: 3582 hours (149 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 9e ae e2 f0  Error: ICRC, ABRT 1 sectors at LBA = 0x00e2ae9e = 14855838

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 40 5f ae e2 f0 00      18:52:17.298  READ DMA EXT
  25 00 40 5f ae e2 f0 00      18:52:17.228  READ DMA EXT
  10 00 3f 00 00 00 f0 00      18:52:17.223  RECALIBRATE [OBS-4]
  25 00 40 5f ae e2 f0 00      18:52:17.097  READ DMA EXT
  25 00 40 5f ae e2 f0 00      18:52:17.097  READ DMA EXT

Error 7 occurred at disk power-on lifetime: 3582 hours (149 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 9e ae e2 f0  Error: ICRC, ABRT 1 sectors at LBA = 0x00e2ae9e = 14855838

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 40 5f ae e2 f0 00      18:52:17.298  READ DMA EXT
  10 00 3f 00 00 00 f0 00      18:52:17.228  RECALIBRATE [OBS-4]
  25 00 40 5f ae e2 f0 00      18:52:17.223  READ DMA EXT
  25 00 40 5f ae e2 f0 00      18:52:17.097  READ DMA EXT
  25 00 08 d7 83 ca f0 00      18:52:17.097  READ DMA EXT

Error 6 occurred at disk power-on lifetime: 3582 hours (149 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 9e ae e2 f0  Error: ICRC, ABRT 1 sectors at LBA = 0x00e2ae9e = 14855838

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 40 5f ae e2 f0 00      18:52:17.298  READ DMA EXT
  25 00 40 5f ae e2 f0 00      18:52:17.228  READ DMA EXT
  25 00 08 d7 83 ca f0 00      18:52:17.223  READ DMA EXT
  25 00 08 d7 dc 96 f0 00      18:52:17.097  READ DMA EXT
  25 00 08 cf dc 96 f0 00      18:52:17.097  READ DMA EXT

Error 5 occurred at disk power-on lifetime: 3582 hours (149 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 9e ae e2 f0  Error: ICRC, ABRT 1 sectors at LBA = 0x00e2ae9e = 14855838

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 40 5f ae e2 f0 00      18:52:17.298  READ DMA EXT
  25 00 08 d7 83 ca f0 00      18:52:17.228  READ DMA EXT
  25 00 08 d7 dc 96 f0 00      18:52:17.223  READ DMA EXT
  25 00 08 cf dc 96 f0 00      18:52:17.097  READ DMA EXT
  25 00 38 07 b9 96 f0 00      18:52:17.097  READ DMA EXT

Error 4 occurred at disk power-on lifetime: 2765 hours (115 days + 5 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 01 be 05 a4 f0  Error: ICRC, ABRT 1 sectors at LBA = 0x00a405be = 10749374

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 38 87 05 a4 f0 00      17:54:12.803  READ DMA EXT
  25 00 38 87 05 a4 f0 00      17:54:12.800  READ DMA EXT
  10 00 3f 00 00 00 f0 00      17:54:12.785  RECALIBRATE [OBS-4]
  25 00 38 87 05 a4 f0 00      17:54:12.783  READ DMA EXT
  25 00 38 87 05 a4 f0 00      17:54:21.991  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     10689         -
# 2  Short offline       Completed without error       00%       108         -
# 3  Extended offline    Completed without error       00%        94         -
# 4  Short offline       Completed without error       00%        93         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

------------- další část ---------------
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 111 minutes for test to complete.
Test will complete after Tue Jan 24 22:15:37 2006

Use smartctl -X to abort test.
smartctl version 5.33 [i686-pc-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     10873         -
# 2  Extended offline    Aborted by host               90%     10872         -
# 3  Short offline       Completed without error       00%     10689         -
# 4  Short offline       Completed without error       00%       108         -
# 5  Extended offline    Completed without error       00%        94         -
# 6  Short offline       Completed without error       00%        93         -



Další informace o konferenci Linux