Re: zdraví disku
Josef Krieglstein
josse na trenet.org
Neděle Listopad 26 17:03:35 CET 2017
Zdravím,
Dle 7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail
Always - 68911493
bych řekl že má problém se trefit, ale může to být normální u té řady
disků, nebo to může být problém mechanického uchycení.
Horší je tohle 187 Reported_Uncorrect 0x0032 072 072 000
Old_age Always - 28
pokud je disk v záruce, chtěl bych nový, pokud je po záruce, pustil bych
badblocks -svw /dev/sde, pokud skončí bez chyb používal bych ho na
nedůležité věci dál. Nevím proč badblocks dokáže spolehlivě přinutit
disk k relokaci, má to umět normálně sám, nebo tu funkci relokace chápu
stále špatně.
Hezký den
Josef Krieglstein
Dne 26. 11. 2017 v 13:36 jaroslav noví napsal(a):
> Ahoj všem,
>
> začal jsem mít drobné potíže s jedním z disků. NAhodile se odpojoval. při pokusu o přimountování hlásil poškozený superblok a podobné veselé zprávy.
>
> Když jsem se kouknul pomocí:
>
> smartctl -x /dev/sde
>
> co mu sau tak chybí dostel jsem výpis:
>
> smartctl -a /dev/sde
> smartctl 6.4 2015-06-04 r4109 [x86_64-linux-4.9.49-gentoo-r1] (local build)
> Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org
>
> === START OF INFORMATION SECTION ===
> Model Family: Seagate Barracuda 7200.11
> Device Model: ST31500341AS
> Serial Number: 9VG0M1L7
> LU WWN Device Id: 5 000c50 01081749b
> Firmware Version: LC1A
> User Capacity: 1 500 301 910 016 bytes [1,50 TB]
> Sector Size: 512 bytes logical/physical
> Rotation Rate: 7200 rpm
> Device is: In smartctl database [for details use: -P show]
> ATA Version is: ATA8-ACS T13/1699-D revision 4
> SATA Version is: SATA 2.6, 3.0 Gb/s
> Local Time is: Sun Nov 26 13:23:57 2017 CET
>
> ==> WARNING: There are known problems with these drives,
> see the following Seagate web pages:
> http://knowledge.seagate.com/articles/en_US/FAQ/207931en
> http://knowledge.seagate.com/articles/en_US/FAQ/207951en
> http://knowledge.seagate.com/articles/en_US/FAQ/207957en
>
> SMART support is: Available - device has SMART capability.
> SMART support is: Enabled
>
> === START OF READ SMART DATA SECTION ===
> SMART overall-health self-assessment test result: PASSED
>
> General SMART Values:
> Offline data collection status: (0x82) Offline data collection activity
> was completed without error.
> Auto Offline Data Collection: Enabled.
> Self-test execution status: ( 249) Self-test routine in progress...
> 90% of test remaining.
> Total time to complete Offline
> data collection: ( 617) seconds.
> Offline data collection
> capabilities: (0x7b) SMART execute Offline immediate.
> Auto Offline data collection on/off support.
> Suspend Offline collection upon new
> command.
> Offline surface scan supported.
> Self-test supported.
> Conveyance Self-test supported.
> Selective Self-test supported.
> SMART capabilities: (0x0003) Saves SMART data before entering
> power-saving mode.
> Supports SMART auto save timer.
> Error logging capability: (0x01) Error logging supported.
> General Purpose Logging supported.
> Short self-test routine
> recommended polling time: ( 1) minutes.
> Extended self-test routine
> recommended polling time: ( 299) minutes.
> Conveyance self-test routine
> recommended polling time: ( 2) minutes.
> SCT capabilities: (0x103b) SCT Status supported.
> SCT Error Recovery Control supported.
> SCT Feature Control supported.
> SCT Data Table supported.
>
> SMART Attributes Data Structure revision number: 10
> Vendor Specific SMART Attributes with Thresholds:
> ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
> 1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 158521203
> 3 Spin_Up_Time 0x0003 090 089 000 Pre-fail Always - 0
> 4 Start_Stop_Count 0x0032 098 098 020 Old_age Always - 2152
> 5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 58
> 7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 68911493
> 9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 16064
> 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 3
> 12 Power_Cycle_Count 0x0032 098 037 020 Old_age Always - 2154
> 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
> 187 Reported_Uncorrect 0x0032 072 072 000 Old_age Always - 28
> 188 Command_Timeout 0x0032 100 098 000 Old_age Always - 38655295497
> 189 High_Fly_Writes 0x003a 068 068 000 Old_age Always - 32
> 190 Airflow_Temperature_Cel 0x0022 061 048 045 Old_age Always - 39 (Min/Max 25/41)
> 194 Temperature_Celsius 0x0022 039 052 000 Old_age Always - 39 (0 18 0 0 0)
> 195 Hardware_ECC_Recovered 0x001a 049 015 000 Old_age Always - 158521203
> 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
> 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
> 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
>
> SMART Error Log Version: 1
> ATA Error Count: 28 (device log contains only the most recent five errors)
> CR = Command Register [HEX]
> FR = Features Register [HEX]
> SC = Sector Count Register [HEX]
> SN = Sector Number Register [HEX]
> CL = Cylinder Low Register [HEX]
> CH = Cylinder High Register [HEX]
> DH = Device/Head Register [HEX]
> DC = Device Command Register [HEX]
> ER = Error register [HEX]
> ST = Status register [HEX]
> Powered_Up_Time is measured from power on, and printed as
> DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
> SS=sec, and sss=millisec. It "wraps" after 49.710 days.
>
> Error 28 occurred at disk power-on lifetime: 16059 hours (669 days + 3 hours)
> When the command that caused the error occurred, the device was active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 01 ff ff ff ef 00 00:52:36.004 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:52:36.002 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:52:36.002 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:52:36.002 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:52:36.002 READ DMA EXT
>
> Error 27 occurred at disk power-on lifetime: 16059 hours (669 days + 3 hours)
> When the command that caused the error occurred, the device was active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 01 ff ff ff ef 00 00:37:26.984 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:37:26.982 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:37:26.982 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:37:26.982 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:37:26.981 READ DMA EXT
>
> Error 26 occurred at disk power-on lifetime: 16059 hours (669 days + 3 hours)
> When the command that caused the error occurred, the device was active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 01 ff ff ff ef 00 00:19:42.216 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:19:42.215 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:19:42.214 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:19:42.214 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:19:42.214 READ DMA EXT
>
> Error 25 occurred at disk power-on lifetime: 16059 hours (669 days + 3 hours)
> When the command that caused the error occurred, the device was active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 01 ff ff ff ef 00 00:17:55.118 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:17:55.108 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:17:55.104 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:17:55.096 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:17:55.089 READ DMA EXT
>
> Error 24 occurred at disk power-on lifetime: 16058 hours (669 days + 2 hours)
> When the command that caused the error occurred, the device was active or idle.
>
> After command completion occurred, registers were:
> ER ST SC SN CL CH DH
> -- -- -- -- -- -- --
> 40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
>
> Commands leading to the command that caused the error were:
> CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
> -- -- -- -- -- -- -- -- ---------------- --------------------
> 25 00 01 ff ff ff ef 00 00:10:27.245 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:10:27.243 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:10:27.243 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:10:27.243 READ DMA EXT
> 25 00 01 ff ff ff ef 00 00:10:27.243 READ DMA EXT
>
> SMART Self-test log structure revision number 1
> Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
> # 1 Extended offline Self-test routine in progress 90% 16064 -
> # 2 Extended offline Completed: read failure 90% 16059 1465644898
> # 3 Extended offline Completed: read failure 90% 16059 1465644884
> # 4 Extended offline Completed: read failure 90% 16059 1465644873
> # 5 Extended offline Completed: read failure 90% 16059 1465645453
>
> SMART Selective self-test log data structure revision number 1
> SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> 1 0 0 Not_testing
> 2 0 0 Not_testing
> 3 0 0 Not_testing
> 4 0 0 Not_testing
> 5 0 0 Not_testing
> Selective self-test flags (0x0):
> After scanning selected spans, do NOT read-scan remainder of disk.
> If Selective self-test is pending on power-up, resume after 0 minute delay.
>
>
> Tipnul bych si, že je skoro s podivem, že ještě žije.
>
> Jak by zhodnotili znalci stav tohodle kousku?
>
> p.s.
> data mám zkopírována na nový disk.
>
> OC
>
> _______________________________________________
> Linux mailing list
> Linux na linux.cz
> http://www.linux.cz/mailman/listinfo/linux
Další informace o konferenci Linux